If you hold surplus assemblies you built in-house and demand no longer absorbs them, taking them apart to recover components may beat leaving them idle. This guide from our homepage walks through the process in the Odoo application, version 19.0. It relies on the Odoo documentation for Unbuild orders 1 and on a GS1 US guideline 2 as a design analogy only.

When Unbuild fits

Unbuild fits items manufactured in-house that have a bill of materials (BoM). Purchased assemblies have no recipe of yours, so don’t dismantle them with the same one. If you need to, design a separate manufacturing workflow that outputs the components as by-products. More context sits on the manufacturing sector page.

Checks before confirming

  1. Input: the product and the quantity to dismantle.
  2. Move locations: the source location holding the assemblies and the destination for the components, such as an inspection location.
  3. Original manufacturing order (MO): link it where applicable.
  4. Correct BoM: if it changed since the build, the resulting components may not match reality.
  5. Lot or serial number if the product is tracked.
  6. Checked on-hand quantity in the Inventory app.

The Odoo 19 documentation says to avoid confirming an unbuild when stock is insufficient, and that unusable components go to scrap 1. Appendix B.1.2 of the GS1 US guideline (R1.0, February 2017) describes a common record, such as a production order, that associates inputs with outputs 2. We borrow only that idea: tie the unbuild to the MO and lot so the trail stays traceable.

A hypothetical example with exact values

This is hypothetical, not a customer story. There are 8 built assemblies on hand, and we dismantle 3. Each assembly holds 1 bracket and 2 clips, so the gross yield is 3 brackets and 6 clips, sent to inspection. After inspection, 1 damaged clip goes to scrap, leaving 5 usable clips. The 3 brackets stay in inspection until a decision is recorded. Assemblies on hand after confirmation: 5.

Item Before After dismantling and inspection
Assemblies 8 5 in stock
Recovered brackets 0 from this operation 3 held for inspection
Recovered clips 0 from this operation 5 usable and 1 scrap out of 6

Reuse, scrap or retain?

  • Reuse: the component passes inspection and meets spec, so move it to usable stock.
  • Scrap: the component is damaged or unusable, so record it with a clear reason.
  • Retain: the decision is pending or no demand is expected, so keep it in inspection or a hold location.

Don’t assume a recovered component’s value equals its original value; agree a valuation policy with finance and test it. Don’t assume an automated quality gate either; inspection is an operational step you define yourselves. To organize the numbers when comparing retain, dismantle and scrap, use the calculators, then decide under your own company policy.

Handoff between teams

The warehouse executes and confirms, quality records each component’s decision, and planning and finance receive the usable balances, the scrap and the valuation policy. Write a handoff note with the order number, MO, BoM, lot, quantities and locations. If you want your setup reviewed, contact us.

Acceptance tests

  1. Balances: after confirming 3 of 8, assemblies on hand show 5, and inspection holds 3 brackets and 6 clips.
  2. Insufficient stock: try a quantity above stock and document the warning. Make stopping and reconciling stock the operating rule, because the warning can allow confirmation.
  3. Scrap: 1 damaged clip is recorded as scrap, and 5 usable clips remain.
  4. Traceability: the record shows the original MO (if any), BoM and lot or serial, and a reviewer can trace components back to the assembly.

FAQ

Can I dismantle a purchased assembly the same way?

No. Use a separate manufacturing workflow with by-products if needed.

Does the Odoo application check quality automatically?

Don’t assume so. Configure the inspection step explicitly and test it.

Is the original MO required?

Link it where applicable, and test the cases where it isn’t available.

Conclusion

Safe disassembly means the right input and locations, a matching BoM, traceability and a checked on-hand balance before you confirm. Return to the homepage for more guides, and to the calculators to organize your decision numbers.

Sources

  1. Odoo 19.0 documentation, Manufacturing: Unbuild orders.
  2. GS1 US, Foodservice Case Traceability Guideline, R1.0, February 2017, Appendix B.1.2.